1. Introduktion
Solenoidventil är en automatisering av grundkomponent som används för att styra vätska, som tillhör ställdonet; Det är inte begränsat till hydrauliskt och pneumatiskt . Solenoidventiler används för att styra riktningen för hydrauliskt flöde . Fabriksmaskiner styrs vanligtvis av hydrauliska cylindrar, så magnetventiler används .}
2. Funktioner
It can work normally under vacuum, negative pressure, and zero pressure, but the diameter generally does not exceed 25 mm. It can also be operated under zero pressure difference, vacuum, or high pressure, but the power is large, and it must be installed horizontally. The upper limit of the fluid pressure range is relatively high, and it can be installed arbitrarily (customization is required), but the fluid Tryckskillnadsvillkor måste uppfyllas .
Tre princip
The pneumatic solenoid valve has a closed cavity with through holes at different positions. Each hole of the pneumatic solenoid valve leads to a different tubing. In the middle of the cavity is the valve. On both sides are two electromagnets. Which side of the magnet coil is energized Where will the valve Kroppen lockas;
The pneumatic solenoid valve blocks or leaks different oil discharge holes by controlling the movement of the valve body, and the oil inlet hole is normally open, the hydraulic oil will enter the different oil discharge pipes, and then the pressure of the pneumatic solenoid valve oil Push the piston of Yugang so that the mechanical movement of the entire solenoid valve is controlled by controlling the current of the electromagnet of the pneumatic magnetventil .
För det fjärde, driftsprincipen för pneumatisk magnetventil
Arbetsläget för den pneumatiska magnetventilen (öppen eller stängd) hänvisar faktiskt till positionen för spolen för den pneumatiska magnetventilen .
The spool is in the A position when the coil is not energized, and in the B position when the coil is energized. When the spool of the pneumatic solenoid valve is in different positions, each interface on the valve body is connected or closed. For example, a two-position solenoid valve means that the spool of the solenoid valve has two different working positions (open or stängd) . För en pneumatisk magnetventil är det magnetventilens elektrifierade tillstånd och avaktiverat tillstånd; for the valve, it controls It is the opening and closing of the valve. Two-way and three-way solenoid valves mean that there are two or three passage ports on the valve body of the pneumatic solenoid valve. The two-position two-way solenoid valve has two channels, one in and one out, and is the most common pneumatic solenoid valve; Tvåpositionens trevägs magnetventil har tre kanaler med en in och två ut, varav två motsvarar anslutningen normalt öppen och normalt stängd . på liknande sätt, treväg, fyrväg och femvägar hänvisar alla till antalet vätskekanaler på ventilkroppen .}
Sex, arbetsprincipen för pneumatisk magnetventil
In the initial position, 1 is the air inlet, 2 is the air outlet (normally open), and 3 is the air outlet (normally closed). 3 and 5 are vent holes. When the solenoid valve coil is energized, the iron core gets the electromagnetic force to make the pilot valve act. Use the 2 and 4 holes to change direction, and discharge the gas in De 2 hålen . Solenoidventilen används för att styra automatiseringen av vätskan . De grundläggande komponenterna tillhör ställdonet; De är inte begränsade till hydrauliska och pneumatiska . Solenoidventiler används för att styra riktningen för hydrauliskt flöde . Fabriksmaskiner styrs vanligtvis av hydrauliskt stål, så magnetventiler används .}
The working principle of the solenoid valve, the solenoid valve has a closed cavity with through holes at different positions, and each hole leads to a different tubing. In the middle of the cavity is the valve. On both sides are two electromagnets, which side is the magnet coil The energized valve body will be attracted to which side, by controlling the movement of the valve body to block or leak out the different drain holes, and the oil inlet hole is normally open, the hydraulic oil will enter the different drain pipes and then pass The oil pressure pushes the oily piston, the piston drives the piston rod, and the piston rod drives the mechanical device to move. In this way, the mechanical movement is controlled by controlling the current of the electromagnet.
Tracing the development history of solenoid valves, so far, solenoid valves at home and abroad are divided into three major categories in principle, and the differences in the structure and material of the valve disc and the differences in principle are divided into six sub-categories ( Direct-acting diaphragm structure, step-by-step structure, pilot diaphragm structure, direct-acting piston structure, step-by-step direct-acting piston structure, Pilotkolvstruktur) .
Pneumatisk magnetventil, som en av de vanliga tillbehören för den pneumatiska ventilen, spelar en mycket viktig roll, främst används för problemet med luftkällvändning av pneumatisk ventil .
Bland dem (2/5) tvåpositionens femvägssolenoidventil används i samband med dubbelverkande pneumatiska ventiler, (2/3) tvåpositions trevägs solenoidventil används i samband med enstaka pneumatiska ventiler, och explosionsprovade coils kan väljas enligt arbetsförhållandena, för att uppnå effekten av explosion, och explosionsprovade coils kan väljas enligt arbetsförhållandena, för att uppnå effekten av explosion, explosion-ex-paps-coils kan väljas enligt arbetsförhållandena, för att uppnå effekten av explosion, explosion-ex-paps-coils kan väljas enligt arbetsförhållandena, för att uppnå effekten av explosion, explosion-ex-paps-coils kan väljas enligt arbetsförhållandena, för att uppnå effekten av explosion, explosion-ex-paps-e-paps-e-paps-e-posten: m II T4, which can work normally at an ambient temperature of -20~60℃. Pneumatic reversing solenoid valves can be mounted on a mount or tube according to actual conditions and valve needs. The installation complies with NAMUR standard and VDI/VDE3845 double hole, the medium is filtered 50 microns, lubricated, or Icke-smörjad tryckluft . Gaskällgränssnittet är ett G1/4-rör .
